set_metrology_model_image_sizeT_set_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size (算子名称)
名称
set_metrology_model_image_sizeT_set_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size — Set the size of the image of metrology objects.
参数签名
描述
set_metrology_model_image_sizeset_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size is used to set or change the
size of the image in which the edge detection that is related to a
metrology model will be performed.
For an explanation of the concept of 2D 度量 see the
introduction of chapter 2D 度量.
The metrology model is defined by the handle MetrologyHandleMetrologyHandleMetrologyHandleMetrologyHandlemetrologyHandlemetrology_handle. The
image width must be specified by the parameter WidthWidthWidthWidthwidthwidth. The image
height must specified by the parameter HeightHeightHeightHeightheightheight.
注意
Note that 该算子 set_metrology_model_image_sizeset_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size should
be called before adding metrology objects to the metrology model
using 该算子s add_metrology_object_genericadd_metrology_object_genericAddMetrologyObjectGenericAddMetrologyObjectGenericAddMetrologyObjectGenericadd_metrology_object_generic,
add_metrology_object_circle_measureadd_metrology_object_circle_measureAddMetrologyObjectCircleMeasureAddMetrologyObjectCircleMeasureAddMetrologyObjectCircleMeasureadd_metrology_object_circle_measure,
add_metrology_object_ellipse_measureadd_metrology_object_ellipse_measureAddMetrologyObjectEllipseMeasureAddMetrologyObjectEllipseMeasureAddMetrologyObjectEllipseMeasureadd_metrology_object_ellipse_measure,
add_metrology_object_line_measureadd_metrology_object_line_measureAddMetrologyObjectLineMeasureAddMetrologyObjectLineMeasureAddMetrologyObjectLineMeasureadd_metrology_object_line_measure,
or add_metrology_object_rectangle2_measureadd_metrology_object_rectangle2_measureAddMetrologyObjectRectangle2MeasureAddMetrologyObjectRectangle2MeasureAddMetrologyObjectRectangle2Measureadd_metrology_object_rectangle2_measure. Otherwise, all
measure regions of existing metrology objects will be
recomputed automatically upon calling set_metrology_model_image_sizeset_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size
or apply_metrology_modelapply_metrology_modelApplyMetrologyModelApplyMetrologyModelApplyMetrologyModelapply_metrology_model.
运行信息
- 多线程类型:可重入(与非独占操作符并行运行)。
- 多线程作用域:全局(可以从任何线程调用)。
- 未经并行化处理。
This operator modifies the state of the following input parameter:
During execution of this operator, access to the value of this parameter must be synchronized if it is used across multiple threads.
参数表
MetrologyHandleMetrologyHandleMetrologyHandleMetrologyHandlemetrologyHandlemetrology_handle (input_control, state is modified) metrology_model → HMetrologyModel, HTupleHHandleHTupleHtuple (handle) (IntPtr) (HHandle) (handle)
Handle of the metrology model.
WidthWidthWidthWidthwidthwidth (input_control) extent.x → HTupleintHTupleHtuple (integer) (int / long) (Hlong) (Hlong)
Width of the image to be processed.
Default:
640
Suggested values:
128, 192, 256, 512, 640, 768, 1024, 1280, 2048
Value range:
0
≤
Width
Width
Width
Width
width
width
(lin)
Minimum increment:
1
Recommended increment:
16
HeightHeightHeightHeightheightheight (input_control) extent.y → HTupleintHTupleHtuple (integer) (int / long) (Hlong) (Hlong)
Height of the image to be processed.
Default:
480
Suggested values:
128, 192, 256, 512, 640, 768, 1024, 1280, 2048
Value range:
0
≤
Height
Height
Height
Height
height
height
(lin)
Minimum increment:
1
Recommended increment:
16
结果
如果参数均有效，算子
set_metrology_model_image_sizeset_metrology_model_image_sizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeSetMetrologyModelImageSizeset_metrology_model_image_size 返回值 2 (
H_MSG_TRUE)
.
如有必要，将引发异常。
可能的前置算子
create_metrology_modelcreate_metrology_modelCreateMetrologyModelCreateMetrologyModelCreateMetrologyModelcreate_metrology_model
可能的后置算子
set_metrology_model_paramset_metrology_model_paramSetMetrologyModelParamSetMetrologyModelParamSetMetrologyModelParamset_metrology_model_param,
add_metrology_object_circle_measureadd_metrology_object_circle_measureAddMetrologyObjectCircleMeasureAddMetrologyObjectCircleMeasureAddMetrologyObjectCircleMeasureadd_metrology_object_circle_measure,
add_metrology_object_ellipse_measureadd_metrology_object_ellipse_measureAddMetrologyObjectEllipseMeasureAddMetrologyObjectEllipseMeasureAddMetrologyObjectEllipseMeasureadd_metrology_object_ellipse_measure,
add_metrology_object_line_measureadd_metrology_object_line_measureAddMetrologyObjectLineMeasureAddMetrologyObjectLineMeasureAddMetrologyObjectLineMeasureadd_metrology_object_line_measure,
add_metrology_object_rectangle2_measureadd_metrology_object_rectangle2_measureAddMetrologyObjectRectangle2MeasureAddMetrologyObjectRectangle2MeasureAddMetrologyObjectRectangle2Measureadd_metrology_object_rectangle2_measure,
add_metrology_object_genericadd_metrology_object_genericAddMetrologyObjectGenericAddMetrologyObjectGenericAddMetrologyObjectGenericadd_metrology_object_generic
模块
2D 度量